Reinitialize your Holosun EPS Carry Red Dot Sight

Wiki Article

Occasionally, you may require to restore your Holosun EPS Carry Red Dot sight to its factory settings. This can be helpful if you've been tinkering with the configurations or are experiencing unexpected behavior. Fortunately, resetting your Holosun is a easy process that can be performed in just a few procedures.

• Begin by ensuring your red dot sight is turned on.
• Identify the small button for reset on the rear of the sight.
• Utilize a thin tool to depress the reset button for approximately three milliseconds.
• Let go the reset button and your Holosun EPS Carry Red Dot sight will power cycle.
• Your red dot sight should now be reverted to its factory settings.

Reset Your Holosun EPS Carry Red Dot toward Defaults

In case you've tweaked your Holosun EPS Carry red dot settings and want to return to original, resetting it to default configuration is a breeze. First, locate the tiny button on the bottom of your optic. Then, keep pressed it for around ten seconds until you see a brief flash. Your Holosun EPS Carry is now reset to its factory settings, ready for precise aiming.

Bring Your Holosun EPS Carry Back to Life

Is your beloved Holosun EPS Carry experiencing some performance problems? Don't despair! A simple factory reset can often solve the problem and get your red dot sight back to its former glory. Before you begin, remember to remove the battery from your Holosun EPS Carry to prevent unexpected activation during the process.

To perform a factory reset on your Holosun EPS Carry, follow these easy steps:

• Press and hold the power button for approximately 7 seconds.
• A message will flash, indicating that the reset is successfuly initiated.
• Stop pressing the power button once the reset is complete.

Your Holosun EPS Carry should now be back to its factory settings. You can connect the battery and confirm your sight's functionality. If you encounter any further troubles, don't hesitate to contactsupport team.

Revert Factory Settings on Your Holosun EPS Carry: A Step-by-Step Guide

Resetting your Holosun EPS Carry to factory settings can be a helpful solution if you're experiencing issues with the optic or simply want to start fresh. This process erases all user configurations and returns the sight to its original state. Before proceeding, remember to note down any customizations you have made as they will be lost during this process. Adhere to these steps carefully to ensure a successful factory reset.

• First, Energize your Holosun EPS Carry by pressing the power button.
• After that, press and hold both the mode button and the up/down adjustment button simultaneously.
• As you continue holding these buttons, tap the power button once.
• The display will show a confirmation prompt indicating that the reset process is initiated.
• Enable the process to finish. This may take a few moments. Once done, your Holosun EPS Carry will automatically shutdown.

After resetting your Holosun EPS Carry to factory settings, you will need to re-enter any desired customizations, such as brightness levels and reticule style. Refer to the user manual for detailed instructions on configuring your optic after a reset.

Clear All Settings on Your Holosun EPS Carry

To Default reset your Holosun EPS Carry sight, you'll need to access the settings menu. This can usually be done by Turning a specific button combination. Consult your Manual for the exact button check here sequence for your model. Once in the settings menu, look for an option that says "Reset All". Select this option and confirm the reset. Your sight will then power off and restart with all settings Reinitialized to their default values.

Reinitialize your Holosun EPS Carry through a Factory Standard Settings

If your Holosun EPS Carry is acting up, a factory reset might be the solution. This will restore your sight to its factory settings, clearing any personalized configurations you've made. To perform this reset, follow these easy steps:

• Initially, find the reset switch on your EPS Carry.
• Secondly, use a fine object, like a pen tip, to activate the reset switch.
• During keep the reset switch engaged, activate your EPS Carry.
• You'll flash a message indicating that the reset is complete.

Once the reset is complete, your EPS Carry will be returned to its factory settings.

Report this wiki page